Orinj Reverb

Not Rated Yet

Orinj version 3.0.0

The Orinj Reverb consists of three distinct operations. First, the original signal is equalized with a three-band parametric equalizer. The purpose of this is to allow the user to create reverbs that are brighter or duller and thus simulate the properties of various rooms. Second, the equalized signal is repeated several times to create distinct repetitions, usually called "early reflections" that create some perception of a room of some size. These repetitions are usually more notable in longer reverbs (i.e., when simulating rooms of larger sizes). Third, the distinct reflections are repeated multiple times with very short delays to simulate natural reverberations. These multiple repetitions with short delays are usually called the "late reverb".

See Reverb for additional information on the properties of natural reverberations and artificial reverbs and for an explanation of the typical implementation of artificial reverbs. Note that some have argued against implementing early reflections in artificial reverbs, since these initial repetitions may sound annoying. To mitigate the strength of early reflections but preserve some perception of the room size, the Orinj Reverb uses a simple chorus on these early reflections and dilutes them, as well as implements separate decay controls for the early reflections and for the late reverb.

Using the Orinj Reverb

The Orinj Reverb can be added to tracks in the multitrack session view, tracks in the loop building view and to waves in the single wave view. In the multitrack session view and in the loop building view, first select the track to which you want to add the effect. In all these views, click on Effect, Reverb, and then on Orinj Reverb in the Orinj menu. You will see a dialog with the two tabs shown below. When this dialog becomes visible, the Orinj Reverb has been added. You can adjust the parameters of the reverb in the dialog and click on Close. These parameters are described below.

Orinj Reverb parameters

See Orinj Effects for notes on how to use the Title, Track, Presets, and Bypass controls. The remaining Orinj Reverb controls are as follows.

The Orinj Reverb dialog – Reverb tab

  • Reverb graph: The reverb graph is a simple representation of the reverb to allow the user to see the impact of each of the reverb controls.
  • Room size: Use these controls – the box and the slider – to set the delay between the original signal and the early reflections (assuming a constant speed of sound of approximately 300 m / s). The room size is measured in squared meters and can be between 1 m2 and 10000 m2.
  • Early decay: Use these controls – the box and the slider – to set the decay of the early reverb reflections. The early decay is the ratio of amplitude of the the early repetition of the signal to amplitude of the the original signal. The early decay is measured in % and can be between 0% (no repetitions) and 100% (no decay and repetitions with the same amplitude as the original signal).
  • Decay: Use these controls – the box and the slider – to set the decay of the reverb tail (the late reverb).
  • Smoothness: Use these controls – the box and the slider – to set how many repetitions there are in the reverb. The "smoother" this reverb is, the more repetitions there are of the signal, and the more the reverb sounds like a single sound mass. The less "smooth" the reverb is, the less repetitions there are, and the more each repetition sounds like a distinct sound. The smoothness of the Orinj Reverb is an index set between -100 and 100, where 100 denotes the most repetitions and -100 denotes the least repetitions. Note that a natural sounding reverb should have a large number of repetitions. Using smoothness settings that are very low, may result in the reverb sounding unnatural, usually metallic.

The Orinj Reverb dialog – Equalizer tab

  • Equalizer graph: This graph shows the intended and actual equalization used by the Orinj Reverb.
  • Frequency bands: Use these controls – the three boxes and three sliders under the equalizer graph – to define the frequency bands of the parametric equalizer. The boundaries of these bands are in the middle between the selected frequency points (where the frequency domain is treated as increasing exponentially and not linearly). The frequency bands can be between 20 Hz and 20 KHz.
  • Precision: Use this slider to define the precision of the equalizer. Larger precision means better separation of frequency bands, but also requires more computational resources (i.e., the effect will be slower).
  • Gain: Use these controls – the three boxes and three sliders to the right of the equalizer graph – to set the gain that will be applied to each of the three frequency bands in the equalizer. The gain is measured in decibels and can be between -20 dB and 20 dB.
  • Equalizer text area: The bottom right corner describes the frequency bands and gains applied to them.
  • Actual equalization: Click on this checkbox to display the actual equalization that will be applied. This actual equalization will be shown in blue and should be similar to the intended equalization shown in yellow. Depending on the precision of the equalizer, however, it may also be slightly different.

See Orinj Effects for additional notes on: where Orinj effects can be used, using boxes and sliders that impact the same parameter (such as the box and slider for the reverb room size), applying effects to mono and stereo waves, and using effects during playback. See Orinj Working with effects for additional information on creating, modifying, moving, removing, and processing effects. See Reverb for additional information on reverbs in audio processing.

Dry and wet mix

The Orinj Reverb supports dry and wet mix changes. That is, you can adjust the mix between the original signal and the reverberations. See Orinj Effects for more information.

The Orinj version 2 Reverb

The Orinj version 2 Reverb dialog – Reverb tab

The Orinj version 2 Reverb differs in two ways: 1) there are more controls for the timing of the early reflections; 2) there are no controls for the decay of the early reflections.

The Orinj version 2 Reverb dialog – Eq tab

The equalizer in the Orinj version 2 Reverb is the same.



  Rating
Rate This Page: Poor Great   |  Rate Content |
Average rating:  No Ratings Yet   
Number of Ratings : 0
  Comments
Add Comment
No Comments Yet


Copyright 2006 by Kaliopa Publishing, LLC