Orinj Simple compressor

Not Rated Yet

Orinj version 3.0.0

The Orinj Simple Compressor adjusts the amplitude of the incoming signal to both soften sharp amplitude changes and, usually, to bring together quieter and louder parts of the signal. This thus is a standard compressor / expander. An explanation of how compressors work is provided in the topic on the Orinj Compressor. The Orinj Simple Compressor differs from the Orinj Compressor in that the Simple Compressor allows for only one threshold and does not permit compressing / expanding separate frequency bands separately.

Using the Orinj Simple Compressor

The Orinj Simple Compressor can be added to tracks in the multitrack session view, tracks in the loop building view, and to waves in the single wave view. In the multitrack session view and in the loop building view, first select the track to which you want to add the effect. In all these views, click on Effect, then on Dynamics, and then on Orinj Simple Compressor in the Orinj menu. You will see the following dialog.

The Orinj Simple Compressor dialog

When the dialog becomes visible, the compressor has been added. Adjust the compressor parameters in the dialog and click on Close. The parameters of the Orinj Simple Compressor are described below.

Orinj Simple Compressor parameters

See Orinj Effects for notes on the Title, Track, Presets, and Bypass controls. The remaining Orinj Simple Compressor controls are as follows.

  • Ratio: Use this slider to set the compression / expansion ratio of the compressor. This is the ratio at which the difference between the amplitude of the signal and the threshold is adjusted. The ratio can be between 10:1 (maximum compression) to 1:10 (maximum expansion). A ratio of 5:1, for example, will mean that the difference between the amplitude of the incoming signal and the compression threshold will be compressed (divided) by 5, if the amplitude of the signal exceeds the threshold.
  • Threshold: Use these controls – the box and the slider – to set the threshold of the compressor. The threshold of the compressor is measured in decibels and can be between -50 dB and 0 dB, where 0 dB is the maximum amplitude that the digital signal can carry, given its sampling resolution.
  • Attack: Use these controls – the box and the slider – to set the attack of the simple compressor. The attack is the time it takes for the compressor to change the amplitude of the signal so that the compression ratio moves from 1:1 (no compression or expansion) to the specified compression or expansion ratio. The attack of the simple compressor is measured in milliseconds (ms) and can be between 0 ms and 200 ms.
  • Release: Use these controls – the box and the slider – to set the release of the simple compressor. The release is the time it takes the compressor to change the amplitude of the signal so that the compression ratio changes from the specified compression ratio back to 1:1. The release is measured in milliseconds (ms) and can be between 0 ms and 2000 ms.
  • Output: Use these controls – the box and the slider – to set the output gain of the simple compressor. This is the gain that will be added to the signal, after it is adjusted by the compressor. The gain is measured in decibels and can be between -20 dB and 20 dB.
  • Forward: Use these controls – the box and the slider – to set the amount of time that the simple compressor looks ahead when adjusting the amplitude of the signal. With value of 5 ms, for example, the compressor will begin to adjust the amplitude of the signal 5 ms before that signal reaches a compression / expansion threshold. This look ahead time parameter is included to allow quick compression at the very beginning of signal peaks, but without a very short attack, since very short attacks can change the underlying form of the signal and introduce distortion. If the attack of the compressor is also set at 5 ms, then the compressor will reach its full compression / expansion ratio at the moment at which the signal reaches the specific compression / expansion threshold. The amount of time that the compressor looks ahead is measured in milliseconds and can be between 0 ms and 10 ms.
  • Peak / moving average: Use these buttons to select whether the compressor should monitor the peaks of the amplitude envelope or an average of the values of the amplitude envelope for an interval of time (see below for the length of the interval). A moving average of the values will make the transitions between amplitudes and the corresponding reactions of the compressor smoother.
  • Average: Use these controls – the box and the slider – to define the length of the interval, over which the compressor will compute and monitor a moving average of the values of the amplitude envelope. The moving average interval is measured in ms and can be between 0 ms and 100 ms.

See Orinj Effects for additional notes on: where Orinj effects can be used, using boxes and sliders that impact the same parameter (such as the box and slider for the compressor attack), applying effects to mono and stereo waves, and using effects during playback. See Orinj Working with effects for additional information on creating, modifying, moving, removing, and processing effects. See Compressor / expander (of dynamics) for additional information on the compressors in audio processing.

The Orinj version 2 Simple Compressor

The Orinj version 2 Simple Compressor dialog

The Orinj version 2 Simple Compressor cannot look ahead and cannot be a moving average compressor. The remaining parameters are the same.



  Rating
Rate This Page: Poor Great   |  Rate Content |
Average rating:  No Ratings Yet   
Number of Ratings : 0
  Comments
Add Comment
No Comments Yet


Copyright 2006 by Kaliopa Publishing, LLC