Orinj Simple reverb

Not Rated Yet

Orinj version 3.0.0

The Orinj Simple Reverb creates many repetitions of the signal to mimic natural reverberations. Natural reverberations occur when the sound bounces between the walls and between the objects in an enclosed space. Since natural reverberations tend to change the frequency content of the signal, the Orinj Simple Reverb also acts as a simple equalizer, usually increasing the amplitude of high frequencies. In Orinj, this is a "simple" reverb, as another effect, the Orinj Reverb, provides more control over the effect.

Using the Orinj Simple Reverb

The Orinj Simple Reverb can be added to tracks in the multitrack session view, tracks in the loop building view, and to waves in the single wave view. In the multitrack session view and in the loop building view, first select the track to which you want to add the effect. In all these views, click on Effect and then on Orinj Simple Reverb in the Orinj menu. You will see the following dialog.

The Orinj Simple Reverb dialog

When this dialog becomes visible, then the Orinj Simple Reverb has been added. You can adjust the parameters of the simple reverb in the dialog and click on Close. These parameters are described below.

Orinj Simple Reverb parameters

See Orinj Effects for notes on how to use the Title, Track, Presets, and Bypass controls. The remaining Orinj Simple Reverb controls are as follows.

  • Pre-reverb delay: Use these controls – the box and the slider – to set the amount of time between the original signal and the first repetition of the reverb. This delay should be relatively short. It is measured in milliseconds (ms) and can be between 1 ms and 100 ms.
  • Early decay: Use these controls – the box and the slider – to set the early decay of the reverb. The early decay is the ratio of each successive repetition of the signal to the previous repetition of the signal. The construction of the simple reverb is similar to an echo, but with many additional repetitions. The early decay is used throughout the reverb. The early decay is measured in % and can be between 0% (maximum decay and no repetitions) and 100% (no decay and repetitions with the same strength as the original signal).
  • Maximum length: Use these controls – the box and the slider – to set the maximum length of the reverb. The maximum length is approximately the distance between the original signal and the last repetition of the reverb. It is measured in milliseconds (ms) and can be between 0 ms and 2000 ms (2 seconds).
  • Smoothness: Use these controls – the box and the slider – to set how many repetitions there are in the reverb. The "smoother" this reverb is, the more repetitions there are of the signal, and the more the reverb sounds like a single sound mass. The less "smooth" the reverb is, the less repetitions there are, and the more each repetition sounds like a distinct sound. The smoothness is measured in % and can be between 0% and 100%. In principle, this reverb is computed as if the sound bounces from the four walls of a standard room. Without any changes, this is considered smoothness of 0%. With smoothness of 100%, there are at least as many new repetitions added as there would have been with 0%.
  • Brightness: Use these controls – the box and the slider – to set the brightness of the reverb. The reverb is equipped with a simple equalizer that increases the amplitude of higher frequencies with higher brightness. The brightness is measured in % and can be between 0% and 100%, where 0% is no additional brightness (no additional amplitude for high frequencies).

See Orinj Effects for additional notes on: where Orinj effects can be used, using boxes and sliders that impact the same parameter (such as the box and slider for the reverb brightness), applying effects to mono and stereo waves, and using effects during playback. See Orinj Working with effects for additional information on creating, modifying, moving, removing, and processing effects. See Reverb for additional information on reverbs in audio processing.

Dry and wet mix

The Orinj Simple Reverb supports dry and wet mix changes. That is, you can adjust the mix between the original signal and the reverberations. See Orinj Effects for more information.

The Orinj version 2 Simple Reverb

The Orinj version 2 Simple Reverb dialog

The parameters of the Simple Reverb in version 2 of Orinj are the same.



  Rating
Rate This Page: Poor Great   |  Rate Content |
Average rating:  No Ratings Yet   
Number of Ratings : 0
  Comments
Add Comment
No Comments Yet


Copyright 2006 by Kaliopa Publishing, LLC